Laserfiche WebLink
SQUARE WALL MOUNT <br />. x of fr <br />8" (203 mm) UP /DOWN CUTOFF <br />• <br />• <br />Ballast <br />Sealing Gasket -- <br />Housing <br />Finish color. <br />bronze <br />Lens Spring-Clip <br />Assembly <br />Hidden from view <br />Diffuse Aluminum <br />Reflector and <br />Ballast Cover <br />Lamp -- <br />(Included) <br />Lampholder -- Ignitor <br />8' (203 mm) <br />BOTTOM VIEW <br />W <br />METAL HALIDE <br />SPEC Any 50W MH SE5405- ha)(b) <br />SPEC ; Any 70W MH SE5407- ia)(b) <br />HIGH PRESSURE SODIUM <br />Any 35W HPS SE5503- (a)(b) <br />Any 50W HPS SE5505- (a)(b) <br />Any 70W HPS SE5507- (a)(b) <br />Specdy (a) Vohage & Iu) Options <br />SPEC a <br />SPEC <br />SPEC x <br />GBIGlAAL DESIWUPf10111s <br />Aluminum die-cast housing supplied. Knockouts <br />are provided on the back of the housing for <br />1/2' conduit entry or for mounting over a single <br />gang box, 4' square or 4' octagon boxes. NOTE: <br />Knockouts are centered 1.6' above centerline of <br />fixture. Two #8 x 1' threaded studs and nuts are <br />provided for mounting over a junction box. <br />Housing also includes 1/2' -14 NPT threaded <br />hubs on three sides for conduit entry. Closed <br />cell neoprene sponge gasketing on the back of <br />the housing provides a watertight mounting <br />seal. Silicone sponge cord gasket between <br />housing and lens ensures a water- and insect - <br />tight seal. Injection molded clear polycarbonate <br />lens and shroud assembly is held in place using <br />a hidden spring clip assembly. Combination of <br />internal painted shroud and diffuse reflector <br />provides controlled uplight and downlight with <br />side cutoff. <br />-- -- 0.25' (6 mm) <br />3.1' (79 mm) <br />Silicone Gasket <br />4.1' (104 mm) <br />Polycartonate <br />Lens <br />Aluminum <br />Shroud <br />Finish color <br />bronze <br />112-14 NPT <br />Threaded Hub <br />UP <br />UP <br />1/2' -14 NPT <br />Threaded Hub <br />Val:11E1E2M SET <br />(r <br />D 120/277V (Standard: 50 - 70W MH) <br />T 120/277/347V (Canada Only) (70W MH) <br />1 120V (Standard: 35 - 70W H PS) <br />2 277V (35 - 70W HPS) <br />3 208V (35 - 70W HPS) <br />4 240V (35 - 70W HPS) <br />6 347V (Canada Only) (50 - 70W MH: 70W HPS) <br />For weage avatabdrty outside the US and Canada. see Bulletin TD-9 or <br />contact vow Ruud Ltgtavq aut onzed Intemabonal Disrnbutor. <br />Fixtures include a clear, medium -base Tamp and <br />porcelain enclosed, 4kv -rated screw -shell -type <br />lampholder with spring - loaded center contact. <br />Lamp ignitor included where required. All ballast <br />assemblies are normal power factor and use the <br />following circuit types: <br />Reactor (120V only) <br />35 - 70W HPS <br />Reactor/Transformer (208, 240, 277V) <br />35 - 70W HPS <br />HX — High Reactance <br />50 - 70W MH <br />ANSI lamp wattage label supplied, visible during <br />relamping. UL Listed in the US and Canada for <br />wet locations and enclosure classified IP54 per <br />IEC 529 and IEC 598. <br />9201 Washington Avenue Racine, Wisconsin 53406 -3772 USA PHONE (262) 886 -1900 <br />1.6' (41 mm) <br />1 (- <br />Notes <br />(10 MPIONS (factory-installed) -- <br />-(a)F Fusing' <br />H High Power Factor Ballast <br />(N /A tor 50W MH or 50 70W HPS with 347V) <br />J Tamperproof Lens Fasteners <br />-(a)P Photocell <br />D Quartz Standby' <br />(includes 100W quartz lamp) <br />Soecdy (a) Single Voltage — See Voeage Sufta Key <br />'Quartz & fuse options are not available together. <br />Housing is standard with our exclusive <br />DeltaGuard° finish, featuring an E-coat epoxy <br />primer with bronze ultra - durable powder <br />topcoat, providing excellent resistance to <br />corrosion, ultraviolet degradation and abrasion. <br />The finish is covered by our seven -year limited <br />warranty. <br />ACCESS(MIEs. <br />TPS -1 Tamperproof Screwdriver <br />FAX (262) 884 -3309 <br />C Ruud Lighting Inc. Printed in USA <br />www. nl ud l ig hti n g. co rr <br />12/11/03 <br />RUUD <br />LIGHTING <br />