Laserfiche WebLink
• <br />• <br />• <br />Lighting Exhibit 4 <br />SOUARE WALL MOUNT <br />8aa (203 mm) UP /DOWN CUTOFF <br />Ballast — Lampholder - Ignitor <br />Sealing Gasket - <br />L. <br />— ODs- (6 mm) <br />3.1" (ra mm) <br />r I . -1- Silicone Gasket <br />\ I <br />4.1'(104 mm) <br />— I- Polycarbonate <br />i Lens <br />Housing <br />Finish color. <br />bronze <br />Lens Spring-Clip <br />Assembly <br />Madden from view <br />Crouse Aluminum <br />Reflector and <br />Ballast Cover <br />(Included) <br />— — 6'(203 mm) - <br />BOTTOM VIEW <br />SPEC */ . ism ' WATTAGE CATALOG # " <br />METAL HALIDE <br />❑ <br />SPEC # Any 50W MH SE5405- fallb) <br />❑ SPEC # -. Any TOW MH SE5407- (a)Ibl <br />- HIGH PRESSURE SODIUM <br />❑ SPEC# - N,y 35WHPS SE5503 -Mb) <br />❑ SPEC# Any 50WHPS SE5505- (a)lb) <br />I] SPEC# Any 70W HPS SE5507-(a)(b) <br />Sorely 11) Vona AIM Options. <br />GENERAL DESCRIPTION <br />Aluminum die -cast housing supplied. Knockouts <br />are provided on the back of the housing for <br />112 conduit entry or for mounting over a single <br />gang box, 4' square or 4' octagon boxes. NOTE: <br />Knockouts are centered 1.6' above centerline of <br />fixture. Two S8 x 1' threaded studs and nuts are <br />provided for mounting over a junction box. <br />Housing also includes 112-14 NPT threaded <br />hubs on three sides for conduit entry. Closed <br />cell neoprene sponge gasketing on the back of <br />the housing provides a watertight mounting <br />seal. Silicone sponge cord gasket between <br />housing and lens ensures a water- and insect - <br />tight seal. Injection molded clear polycarbonate <br />Tens and shroud assembly is held in place using <br />a hidden spring clip assembly. Combination of <br />internal painted shroud and diffuse reflector <br />provides controlled upligM and downlight with <br />side cutoff. <br />- - Aluminum <br />Shroud <br />Finish color <br />bronze <br />, 11241 <br />reads' Me <br />(a) VOLTAGE SUFFIX KEY <br />D 12012T7V (Stallard: 50 - 70W MH) <br />T 120277)347V (Canada Orly) (70W MH) <br />1 120V (Standard: 35- 70W HPS) <br />p <br />277V (35 -70W HPS) <br />3 201iV (35 - 70W HPS) <br />4 240V(35- 71WHPS) <br />6 347V (Oaf Only) (50 -Mir MH: 70W HPS) <br />For HAW aaYeily mama as Mad rimdL s Mom )V- a <br />rased your Red L*aq ausmma Iwenaame OWnt or. <br />ELECTRICAL <br />Fddures include a clear, medium -base Tamp and <br />porcelain enclosed, 41(v-rated screw -shell -type <br />lampholder with spring - loaded center contact <br />Lamp ignitor included where required. All ballast <br />assemblies are normal power factor and use the <br />following circuit types: <br />Reactor(120V only) <br />35 - 70W HPS <br />Reactor/Transformer (208. 240, 277V) <br />35 - 70W HPS <br />HX - High Reactance <br />50 - 70W MH <br />LABELS <br />ANSI lamp wattage label supplied, visible during <br />relamping. UL Listed in the US and Canada for <br />wet locations and enclosure classified IP54 per <br />IEC 529 and IEC 598. <br />9201 Washington Avenue Racine, Wisconsin 53406 -3772 USA PHONE (262) 886 -1900 <br />SE5 -8 <br />SERIES <br />Notes <br />(b) OPTIONS (factory - install d) <br />-(a)F Fusing' <br />H High Power Factor Ballast <br />(UA for 50W MH or 50- 70W HPS with 347V) <br />J Tamperproof Lens Fasteners <br />ia■P Photocell <br />0 Quartz Standby' <br />(Includes 100W quartz laew) <br />Sorely fa) Sings Vamp -See Votes Suns Der <br />'Manz a her optimism not available tougher <br />FINISH <br />Housing is standard with our exclusive <br />DeltaGuard• finish, featuring an E-coat epoxy <br />primer with bronze ultra -durable powder <br />topcoat, providing excellent resistance to <br />corrosion, ultraviolet degradation and abrasion. <br />The finish is covered by our seven -year limited <br />warranty. <br />ACCESSORIES <br />TPS -i Tamperproof Screwdriver <br />FAX (262) 884-3309 <br />0 Ruud Lighting inc. Piloted in USA <br />www.tuudigMing.cmr <br />12711103 <br />RUUD <br />LIGHTING <br />Apollo Landing Site Design Standards <br />page 23 <br />