Loading...
HomeMy WebLinkAbout2003-073 Council ResolutionCITY OF LINO LAKES RESOLUTION NO. 03-73 RESOLUTION APPROVING AMENDMENT OF AN EXISTING CONDITIONAL USE PERMIT TO ALLOW TWO BUILDING ADDITIONS AT MOLIN CONCRETE, 415 LILAC DRIVE WHEREAS, Molin Concrete has submitted a request to the City to amend an existing conditional use permit to allow for building additions for a locker room and the expansion of a maintenance garage at 415 Lilac Drive, and WHEREAS, the legal description of the property is: The South Half of the Northwest Quarter of the Southwest Quarter of Section 8, Township 31, Range 22, Anoka county, Minnesota; The Southwest Quarter of the Southwest Quarter of Section 8, Township 31, Range 22, EXCEPT the East 260 feet of the South 832 feet thereof, ALSO EXCEPTING the South 412 feet of the Southwest Quarter, Anoka County, Minnesota The South 412 feet of the Southwest Quarter of the Southwest Quarter of Section 8, Township 31, Range 22, Anoka County, Minnesota, EXCEPT the East 260 feet thereof. WHEREAS, the City's review is based on architectural and structural plans received April 8, 2003; preliminary grading plan, photometric plan, and lighting fixture cut sheets received April 21, 2003, and WHEREAS, the Planning Commission held a public hearing on the application on May 14, 2003, and recommended approval with conditions, and WHEAREAS, the City Council of the City of Lino Lakes adopted Resolution 01 -182 on November 13, 2001, and WHEREAS, the City Council of the City of Lino Lakes finds that, with the conditions of approval included in this resolution, the following findings of fact apply as required by Section 2 Subd. 2.B.7 and by Section 8 Subd.2.I.4 of the zoning ordinance: a. This application is consistent with the comprehensive plan, including future and present land uses. The building additions do not alter existing uses on the site. The application meets all performance standards. b. c. The project will not increase traffic generation or impacts. d. The project will not increase demands on sanitary sewer and water use. e. The project will require not require capital improvements by the City. f. The project will not create detrimental impacts. g. The project will not impact natural or historic features. h. All applicable Minnesota Pollution Control Agency requirements are satisfactorily met. i The project will not alter the site's drainage system previously approved by the City Engineer. NOW, THEREFORE, BE IT RESOLVED, that the Lino Lakes City Council hereby approves amendment of the existing conditional use permit to allow the construction of building additions for a locker room and the expansion of a maintenance garage. BE IT FURTHER RESOLVED that the following conditions apply: 1. The City Engineer's comments in the May 6, 2003 TKDA memo must be satisfied.. 2. Exterior lighting fixtures shall be hooded and directed to reflect light away from neighboring residential properties and rights -of -way. The fixtures must have a 90 degree cut off angle. 3. All conditions in Resolution 01 -182 continue to apply. Adopted by the Lino Lakes City Council this STAFF ORIGINATOR: C. C. MEETING DATE: AGENDA ITEM 7 B Jeff Smyser May 27, 2003 TOPIC: Resolution 03 -73 Conditional Use Permit Amendment Molin Concrete VOTE: 3/5 BACKGROUND Molin Concrete proposes to construct two building additions. One is a 950 sf locker room. The other is a 3100 sf expansion of a maintenance garage. The Molin property is covered by a conditional use permit for the concrete plant. The northern 20 acres is covered by an interim use permit for outdoor storage. This new application does not involve the storage area. The conditional use permit (CUP) covers the entire site. Building additions require an amendment to the CUP. Because this application involves the CUP amendment, it is appropriate to review conditions placed on the site through the last CUP amendment in 2001 (Resolution 01- 182). Under the new zoning ordinance, the site plan review is done administratively. However, a CUP amendment is necessary, and a site plan review is part of the CUP review.. Therefore, this report includes a site plan review. ANALYSIS The following chart describes the Zoning and Land Use designation of the subject site, as well as surrounding properties: Location Land Use Zoning Subject Site Industrial General & Light Industrial North Low Density, Unsewered Residential Rural East Industrial & Commercial Rural South Industrial General Industrial West . Low Density, Unsewered Residential R -1 Residential Single Family and Rural Molin May 27, 2003 page 2 SITE PLAN Buildings: Site plans have been submitted for two additions. One is for a 950 sq. ft. locker room facility. The addition will be located on the southern side of the existing manufacturing building, adjacent to Lilac Street. The addition meets all required setbacks. The second proposed addition is for a 3,100 sq. ft. expansion of an existing maintenance garage. This addition will be located on the northern side of the main Lilac St. parking area The addition meets all required setbacks. Architectural elevations show that the exteriors of the proposed two additions will complement the existing buildings. The maintenance garage will have a heavy brush finish. The locker room will be smooth, painted concrete, like the existing building to which it will be attached. Lighting: The photometric plan indicates that the project complies with City requirements regarding lighting intensity at the property lines. As a condition of approval for the previous Conditional Use Permit Amendment granted in 2001 (Resolution No. 01 -182), the site is subject to specific lighting fixture requirements (see conditions #7 & 8). These requirements state that lighting shall be "hooded and directed to reflect light away from neighboring residential properties and rights -of -ways. The fixture details submitted for the proposed two additions are hooded, but they must be mounted so light is downward - directed. That is, they must be mounted parallel with the ground, so there is 90 degree cut off angle. Traffic: The building additions are to accommodate current activity on site. They will not increase the number of employees or the amount of traffic generated by the concrete plant. The City has received no recent calls about trucks parking on Lilac St. Grading/Drainage, Utilities: A grading plan and utility plan have been submitted for the site. The City Engineer's comments are attached. No new utilities will be needed for the building additions. Landscaping: The maintenance garage is at an internal location on the site and is almost entirely surrounded by other buildings. The new locker facility addition is dwarfed by the existing manufacturing building, and the front of the site is fenced with a screening wall. There is no landscaping proposed for the two additions. Staff does not recommend any Completion of a number of landscaping issues was a condition of approval for Molin's previous Conditional Use Plan Amendment (Resolution No. 01 -182), given in November of 2001, for an expansion of the Molin facilities. These landscaping issues involved tree Molin May 27, 2003 page 3 and shrub planting on the berm to the north of the property, as well as native seed planting around the pond located north of the berm. Because of the wet weather last summer, excavation and landscaping were delayed on the northern portion of the Molin site. Molin did notify City staff of this problem last year. Staff visited the site on May 2nd this year to view progress. The landscaping plan is being implemented properly, according to the approved planting plan. Some acceptable substitution of a few individual plantings has occurred. Molin has almost completed construction of the swale and pond through the property. When they are finished, landscaping can be completed. PLANNING & ZONING BOARD RECOMMENDATION The P & Z held a public hearing on the application on May 14 and recommended approval with the conditions listed below and in the resolution. RECOMMENDATION Staff recommends approving Resolution 03 -73 amending the CUP with the following conditions: 1. The City Engineer's comments in the May 6, 2003 TKDA memo must be satisfied. 2. Exterior lighting fixtures shall be hooded and directed to reflect light away from neighboring residential properties and rights -of -way. The fixtures must have a 90 degree cut off angle. 3. All conditions in Resolution 01 -182 continue to apply. This report is based on architectural and structural plans received April 8, 2003; preliminary grading plan, photometric plan, and lighting fixture cut sheets received April 21, 2003. CITY OF IN V KE Memorandum DATE: May 7, 2003 TO Mike Grochala FROM: James E. Studenski, City Engineer RE: Molin Concrete Products Attached is a TKDA memorandum dated May 6, 2003, reviewing the Molin Concrete Products building additions. The project is in general conformance with City requirements. The memorandum items must be addressed prior to approval being given for this project. Please contact me at 651/982 -2430, with any questions. . 600 Town Center Parkway, Lino Lakes, Minnesota 55014-1182 Phone: 651- 982 -2400 • Fax: 651- 982 -2499 o TDD: 651 - 982 -2410 TKDA *ENGINEERS • ARCHITECTS • PLANNERS MEMORANDUM 1500 Piper Jaffrey Plaza 444 Cedar Street Saint Paul, MN 55101 -2140 (651) 292-4400 (651) 292 -0083 Fax www.tkda.com To: James Studenski, City Engineer Reference: Molin Concrete Products Company Copies To: From: Scott A. Brink 64-6 j ,q Date: May 6, 2003 / City of Lino Lakes, Minnesota Comm. No. 12701 -002 Routing:. The proposed plans provide for building additions to the exist Molin Concrete Products Facility located at the intersection of Lilac Street and Fourth Avenue. The additions consist of a restroom addition (approximately 1000 sq. ft.) to the existing building (75,000 sq. ft.) and a maintenance garage addition (approximately 3200 sq. ft.) to the existing office garage. A set of Architectural and Structural plans have been submitted to the City of Lino Lakes, along with a site utility plan. The following review comments are based upon Sheet Cl (utility plan) prepared by Plowe i Engineering, Inc., dated March 14, 2003. Comments 1. The project site is located at the northeast comer of the intersection of Lilac Street and Fourth Avenue. The proposed building additions and associated utility work all occur on private property and connect to existing private utility lines. The private lines serving the proposed additions are 8 -inch diameter sanitary sewer and 8 -inch diameter watermains, all adequate in size to accommodate the proposed additions. However, the Contractor shall coordinate all proposed utility connections in accordance with the City of Lino Lakes' requirements for building permits and associated utility connections. The Contractor shall adhere to working hours for construction activities in accordance with the requirements of the City of Lino Lakes. The Contractor shall provide a sweeper to clean streets and paved areas outside of the project site on a daily basis as needed. The Contractor shall install silt fence and erosion control measures around all disturbed areas. A note must be added that the City of Lino Lakes Utility Supt. shall be contacted at least 48 hours prior to any utility work, utility connections, or any work in the public right -of -way is performed. An Employee Owned Company Promoting Affirmative Action and Equal Opportunity :Violin Concrete Products Company Page 2 May 6, 2003 City of Lino Lakes, Minnesota i A note must be added that all sanitary sewer and watermain installed as part of this project shall be installed, tested, and accepted per the requirements of the City of Lino Lakes, specifications of the City Engineers Association of Minnesota, the Minnesota Department of Health, and the Minnesota Pollution Control Agency, as required. Sanitary sewer service pipe shall be SDR 26 or SCH 40 and ductile iron water pipe shall be CL 52. Gate valves shall be Mueller A- 2370 -20 with mechanical joints, meeting AWWA Specifications C500 -61. Valve Boxes shall be Mueller H -10357 with H -10361 drop lid and extensions shall be Mueller H- 10363. At this time, it does not appear that the proposed improvements will require a review or approval from the Rice Creek Watershed District since the area to be disturbed is less than 2.5 acres. However, a review may be warranted if the improvement site is located within a 100 -year floodplain, or within 1,000 feet of a public water or protected wetland. There is a wetland identified on Sheet C 1 within 1000 feet of the improvements. However, this wetland does not appear to be identified on the NWI map. Existing drainage patterns must be maintained. April 4, 2003 Since 1897 CONCRETE PRODUCTS COMPANY Dear Neighbors This letter is to inform you that Molin Concrete is planning on two small building additions at the south end of our property. These additions are for support purposes and do not include production space. Included in this mailing are two sheets that give information about these plans. We anticipate that our application for approval will be discussed during the May Planning and Zoning meeting. The first sheet shows a site plan for Molin Concrete. On this site plan, you will see the location of the two proposed additions (both are labeled and highlighted in black). The second sheet provides the layouts of the proposed additions. The additions are: 1. Restroom / Locker facility — This is a 950 square foot addition for our employees that work in the plant. This addition is long overdue and will provide our employees with a facility that is large enough to handle their needs. Maintenance Garage addition — This is a 3,100 square foot addition to the current maintenance shop. The existing maintenance shop is in the lower level of the small two -story building on our property. The current facility is too small for much of our equipment. We currently have to perform some normal maintenance (oil changes, equipment washing, and tire changing) outside. This addition will allow us to drive our equipment into the building for maintenance. Our maintenance personnel will appreciate being inside on rainy or winter days. We would like to extend an invitation to you to stop by Molin Concrete on April 17th between 4:30 and 6:30 p.m. Tom Molin, Randy Molin and Mark Groff will be available to show you the plans for the additions and answer any questions you may have. If you need to come at some other time, please call ahead so that we can make sure that one of us is available. Sincerely, Molin Concrete Products Company Tom Molin Randy Molin President Vice President Mike Grochala, City of Lino Lakes Planning and Zoning Members City Council Members Mark Groff Chief Financial Officer OUR MISSION IS "BUILDING" CUSTOMER SATISFACTION THROUGH GENERATIONS OF TEAMWORK Flexicore Hollowcore Plank • Wallpanels • Beams and Columns • Misc. Precast • 415 Lilac Street • Lino Lakes, Minnesota 55014 • Office 651 - 786 -7722 • FAX 651 - 786 -0229. 1- 800 - 336 -6546 • EOE/AA CITY OF LINO LAKES RESOLUTION NO. 01-182 RESOLUTION APPROVING AMENDMENT OF AN EXISTING CONDITIONAL USE PERMIT, APPROVING AMENDMENT OF AN EXISTING INTERIM USE PERMIT, AND APPROVING A SITE PLAN REVIEW FOR MOLIN CONCRETE AT 415 LILAC DRIVE WHEREAS, Molin Concrete has submitted a request to the City to amend an existing conditional use permit, amend an existing interim use permit, and approve a site plan review for new facilities at 415 Lilac Drive, and WHEREAS, the Planning Commission opened a public hearing on the application on September 11, 2001, closed the public hearing on October 10, 2001, and recommended approval with conditions, and WHEAREAS, the City Council of the City of Lino Lakes adopted Resolution 01 -171 on October 22, 2001, but subsequent information necessitates reconsideration of the conditions included in that resolution, and WHEREAS, the City Council of the City of Lino Lakes finds that, with the conditions of approval included in this resolution, the following findings of fact apply as required by Section 2 Subd. 2.B.7 and by Section 8 Subd.2.I.9 of the zoning ordinance: a. This application will not be detrimental to or endanger the public health, safety, comfort, convenience or general welfare of the neighborhood or the City. b. This application will be harmonious with the general and applicable specific plans and policies of the comprehensive plan of the City and this ordinance. This application will be designed, constructed, operated, and maintained so as to be harmonious and appropriate in appearance with the existing and/or intended character of the general vicinity and will not change the essential character of that area d. This application will be served adequately by essential public facilities and services, including streets, police and fire protection, drainage structures, refuse disposal, water and sewer systems, and schools; or will be served adequately by such facilities and services provided by the persons or agencies responsible for the establishment of the proposed use e. This application will not create excessive additional requirements at public cost for public facilities and services and will not be detrimental to the economic welfare of the .community. f. This application will not involve uses, activities, processes, materials, equipment and conditions of operation that will be detrimental to any persons, property, or the general welfare because of excessive production of traffic, noise, smoke, fumes, glare, or odors. g. This application will have vehicular approaches to the property which are so designed as not to create traffic congestion or an interference with traffic on surrounding public thoroughfares. h. This application will not result in the destruction, loss, or damage of a natural, scenic or historic feature of major importance. This application will conform to specific standards of this ordinance applicable to the particular use. . All applicable Minnesota Pollution Control Agency requirements are satisfactorily met. k. A drainage system subject to the approval of the City Engineer shall be installed. Storage areas are landscaped, fenced and screened from view of neighboring uses, abutting residential zoning districts and public rights -of -way in compliance with Section 3, Subd. 4.S. m. Vehicular access points shall create a minimum of conflict with through traffic movement and shall be subject to approval of the City Engineer. n. All signing and informational or visual communication devices shall be compliance with the applicable provisions of Appendix C of the City Code. o. Provisions shall be made to control and minimize noise, air and water pollution. p. All conditions pertaining to a specific site are subject to change when the Council, upon investigation in relation to a formal request, finds that the general welfare or public betterment can be served as well or better by modifying the conditions. NOW, THEREFORE, BE IT RESOLVED, that the Lino Lakes City Council hereby approves amendment of the existing conditional use permit, approves amendment of the ' existing interim use permit, and approves the site plan review for 415 Lilac Drive, BE IT FURTHER RESOLVED that the following conditions apply: 1. All permits /approval required by the Rice Creek Watershed District, including drainage and grading and wetland delineation, shall be obtained prior to any site grading. The Watershed permit applies to the overall conditional use permit for the concrete plant, covering the entire site, as well as the site plan review. 2. Final utility, grading, and drainage plans must obtain approval from the City Engineer prior to site grading or building permit. This condition applies to the overall conditional use permit for the concrete plant, covering the entire site, as well as the site plan review. . If off -street parking creates safety concerns in the future, the City shall re- examine the parking needs and shall require additional parking spaces. This condition applies to the overall conditional use permit for the concrete plant, covering the entire site. 4. Proper building permits must be obtained prior to any construction of the new building. All proposed structures shall comply with applicable City building material requirements. An escrow shall be established according to City policy as part of the building permit to insure completion of all site improvements. This condition applies to the site plan review. 5. The approval of the site plan and amended conditional use permit includes the 70± foot height of the cement silos, as provided by Sec. 3. Subd 4.C.3. of the zoning ordinance, which allows a building height to exceed the zoning district standard with a conditional use permit. The need for the increase in height has been demonstrated and it does not violate the intent or character of the GI zoning district. The site is capable of accommodating the increased structure size. The silos will not increase traffic volumes or need for public services. The proposal meets the required increased setbacks and does not limit solar access. The surfacing material of the site as shown on the. submitted site plan and grading plan is acceptable. Additional bituminous areas may be paved and additional crushed asphalt may be applied without additional review by the City. This condition applies to the overall conditional use permit for the concrete plant, covering the entire site. 7. Outdoor lighting is prohibited in the site's outdoor storage area (north of 77' St./Thomas St.). Permissible exterior lighting on the southern portion of the property shall be hooded and directed to reflect light away from neighboring residential properties and rights -of -way. This condition applies to the overall conditional use permit for the concrete plant, covering the entire site, as well as the interim use permit on the northern portion. 8. Lighting fixtures on the new building shall be the Lithonia Lighting KAD model of the Contour Series with a lens that does not extend below the fixture (as submitted to the City 10/10/2001). Lighting fixtures on the new overhead crane shall be the FP Option of the Lithonia Lighting KACM model of the Contour Series with a lens that does not extend below the fixture (as submitted to the City 10/16/2001). This condition applies to the site plan review. 9. The site's western access point (from 4th Avenue) shall remain at the 77`1 St./Thomas St. alignment. Access to Lilac St. shall be maintained as on the plans received by the City August 13, 2001. This condition applies to the overall conditional use permit for the concrete plant, covering the entire site, as well as the interim use permit on the northern portion. 10. A minimum 150 -foot setback shall be maintained along the site's northern boundary. The buffer yard consisting of a berm with plantings shall extend 40 feet north into this 150 -foot setback line (i.e., the berm shall be maintained in the southern part of the 150 -foot setback). The berm shall be maintained at an eight foot height. This condition shall apply to both the overall conditional use permit on the entire site for the concrete plant as well as the interim use permit in the northern portion. 11. Trucks serving Molin shall not park along Lilac Street. Molin and its agents shall inform drivers of this condition. This condition shall apply to the overall conditional use permit on the entire site for the concrete plant. 12. All applicable MPCA requirements shall be satisfactorily met. This condition shall apply to the overall conditional use permit on the entire site for the concrete plant. 13. The following noise mitigation efforts shall be utilized: a. The outdoor storage yard on the northern portion shall be arranged such that truck backing maneuvers toward residential properties are minimized. This condition applies to the interim use permit. b. Molin equipment and trucks shall be outfitted with strobe lights to replace backup beepers during nighttime hours (6:00 p.m. to 8:00 a.m.). Because use of strobes rather than beepers has been approved by the Minnesota Dept. of Labor and Industry, OSHA, this condition shall apply to both the overall conditional use permit on the entire site for the concrete plant as well as the interim use permit in the northern portion. However, this prohibition on beepers does not apply to semi - tractors that are not owned by Molin operating on the southem (GI zone) portion of the property. Nor does this prohibition apply to equipment being used on construction projects anywhere on the site If, in the future, there is some reason under law why the strobes are not sufficient, Molin shall be required to apply for an amendment to the conditional use permit and interim use permit. c. There shall be no outdoor cutting, sawing, grinding, or similar activity anywhere on the site before 8:00 a.m. on Saturdays. (This prohibition does not apply to truck loading or movement of product.) This condition applies to the conditional use permit for the concrete plant covering the entire site d. There shall be no shuttle lifts, fork lifts, trucks, or other equipment operated in northern interim use permit area earlier than 8:00 a.m. on any day. This condition applies to the interim use permit. e. Upon issuance of the certificate of occupancy for the new extruded precast manufacturing building, operating hours for shuttle lifts shall be no earlier than 7.00 a.m. and no later than 8:00 p.m. anywhere on the site on any day. This applies to the conditional use permit on the entire site and the interim use permit on the northern portion. 14. a. The new landscaping plan dated received by the City October 10, 2001 shall be the approved plan with the addition of plantings described in 14.b. All plantings shall be in place by June 2002. Plantings shall be maintained in a healthy state. Dead plantings shall be replaced in a timely manner. This condition applies to the overall conditional use permit on the entire site for the concrete plant as well as the interim use permit for storage in the northern portion of the site b. A double row of staggered conifers shall be planted along the northern Molin property line. They shall be minimum five feet tall when planted. Trees in each row shall be planted 36 feet apart to achieve the effect of a tree every 18 feet when viewed horizontally. (The wetland/pond may necessitate some variation to that pattern, however.) No trees are required to be planted along the western 230 feet. A conifer species with a maximum height of 30 feet shall be planted along the next 420 feet moving east White or red pines shall be planted along the eastern 640 feet. 15. The interim use permit on the northern portion, zoned LI, allows for storage, not production. No production or finishing activities shall be conducted in this area. This includes cutting, grinding, and other such work. 16. The interim use permit will expire if there is a change in the land use in the LI District on the northern portion of the site 17. The following conditions that were approved on October 27, 1997 shall no longer apply - condition 11 a. requiring storing wall panels parallel to the buffer yard (berm); - condition 13 c. requiring a solid row of coniferous trees on the north side of the berm and a row of deciduous trees on the south side of the berm; -condition 13 e. requiring irrigation for the berm. 18. The existing outdoor core slab casting bed (outdoor concrete pouring) shall be eliminated as soon as the new extruded precast manufacturing building is completed. This condition shall apply to the site plan and the conditional use permit covering the entire site. BE IT FURTHER RESOLVED that Resolution 01 -171 is hereby made null and void. BE IT FURTHER RESOLVED that the review and approval is based on the following: Grading, Drainage and Erosion Control Plan Plowe Engineering received 8/13/01 Utility Plan Plowe Engineering received 8/13/01 Wetland Mitigation Plan Plowe Engineering received 8/13/01 Set of Architectural, Structural, Mechanical Plans Professional Design Group received 8 /13/01 dated August 7, received August 8 Professional Design Group received 10/102001 Professional Design Group received 9/26/01 received 10 /10 /01 and 10/16/01 Professional Design Group received 9/11/01 and 9/28/01 Letter from Randy Molin Planting Plan, revised, Photometric Plan Lithonia Lighting Fixture Information Solar (shadow) Analyses Adopted by the Lino Lakes City Council this ) 3 day of in , 2001 John J. Bergeson, Mayor aRTI:11 AVENUE 000 00000000000'0000000000000 MAINTENANC GARAGE DDITION RESTROOM ADDITION r O This cutoff luminaire has an optical system spedfically designed to assure maximum rain beam projection, while minimizing spill light. It is generally positioned with a 20' tilt back from vertical to reduce glare and obtain optimum performance. The optical Z chamber is sealed to reduce dirt and insect contamination. This tbdure is ideal for small parking areas and building - mounted security lighting. H PP °141,44•ZIN P4000 �,'4 ■ I F 8000 , so Candlepower Distribution Curve of 175W MH Cutoff Floodlight, 20* tilt above horizontal. 404040 a0 0 20 40 40 10 42.7 Ise Ins 244 122 122 2.1 012 22 0.1 242 122 122 2.1 014 01 122 10.1 212 Isolootcandle plot of one 175W MH Cutoff Floodlight at 15' (4.6 m) from reference plane and 20* St r work, tar betAlimi ?°' Wif-04441 IVNtip *# if • Candlepower Distribution Curve of 150W HPS Cutoff Floodlight, 20'tilt above horizontal 40 120 40 WO 140 120 140 40 @ 40 20 20 40 Wattage! Lamp 150W PSMH 50W MH 70W MH 100W MH 175W MH 35W HPS 50W HPS 70W HPS 100W HPS 150W HPS `J ESe Catalog Number LCF•615 -M LCF*405 -D LCF,407 -D LCFA10 -D LCF'417 -M LCF503 -1 LCFJg5 -D LCF'507 -M LCF_510 -M LCF'515 -M Quiet ! ifor`mation 7_`'- Mounting Code (Used Code at ` In Catalog 8) 3 a2' Adjustabb Fitter 4 =Yoe Mount 8 =Without Mounting (hardware) (factory- drilled) LU AI-Z. k o ( 'r Options: (Factoip-osfalled) Change Add Alter Description Suffix To Sutton 277V Reactor Ballast ( aa44 27 120V Rotor ballast (50-150W HPS only) 1 48W ballast (175W MH & 70 -100W HPS only) 5 Quad -volt ballast (50-100W MH only) M Tri- vol ballast (7o- rgw Ina m- 1marresararltr ohm T Single Fusel (277V Rmclor,120V, 27N or S47V) 27,1, 2 or 6 F Dual Fuse* (208V, 240V or480V) 3, 4 ors F Tamperproof Lens Fasteners J Button Photocell* (Factory- Medalled with all mountings other than 2' Adjustable Filter) NOTE on on 480V 27,1,2,3, 4 orb P External Photocell* (Fa Cory- installed) (page 123) Forfi>dseswl4&N 5 P • Mures with factory= installed photocell and/or fuse supplied with single voltage ballast Accessories` (Flsld- lastatied) Description Catalog 1 Wire Guard FNG-L Polytarbonate Vandal Shield (n/a it rodure is used In an uptight position) LS-L Tamperproof Screwdriver TPS-1 Button Photocell (Plaid - Installed in fixtures with 2' Adjustable Fitter) For Endures wt120V PC-1 For fixtures w/208, 240 or 277V PC-2 For ibdures w/347V PC *6 Optical Systems Page 115 Mountings Page 116 Catalog Number Loglslffotiage Suffix Key Page 116 Accessories Page 123 Mounting Alteratives Pages 124 -125 Monolog Brackets Pages 126 -127 Poles Pages 128 -133 v sa • u 244142 122 21 0m 4.1 122 122 244 Isofootandte plot of one 150W HPS Cutoff Floodlight at 15' (4.6 m) from reference plane and and 20' tilt U This cutoff Iuminaire has an optical system specifically designed to assure maximum main beam projection, while minimizing spill Tight. It is generally positioned with a 15' to 25' tilt above horizontal to reduce glare and obtain optimum performance. Z The CF Series can be used for parking lots, auto sales lots and outdoor sports areas (volleyball, tennis courts, etc.). Thee Sizes: 12' square x5' deep (305x127mm) 16' square x 6.5' deep (406 x 165 mm) 22' square x 9.25' deep (559 x 235 mm) 0 ,rirroz Nr"":"w I ee4*> o��1 Candlepower Distribution Curve of 400W HPS Cutoff Hoodlight, 20' tilt above horizontal 10 e0 40 eD 140' ! i O ea 40 10Vias 42.7 21111 905 24.4 113 - 122 u Om 11 40 _ -_ —` lee 9 111192 111 em 1 111 122 3 244 WO N Isofootrandle plot of one 400W HPS Cutoff Floodlight at 30' (9.1 m) mounting height, and 20* tilt above horizontaL rioliParsTo iro-z. Via 41Pei I St#4 Candlepower Distribution Curve of 1000W HPS Cutoff Floodlight, 20' tilt above horbnntaL 100' 24.4 40� 1122 ay =au 1123(411312211 0m a1 102113 sums Isofootcandle plot of one 1000W HPS Cutoff floodllgM at 40' (12.2 m) mounting height, and 20' Olt above horlzontaL Mowing Wattage) Catalog 81ze (sq.) Lamp tlembsr ' 12' 150W KIM MCF_815 -M Moaatlog Coln (hoed Code al! In Catalog 1) 3 -2' Adjustable Fllter 16' 320WPSNt1 CF•632 -M 4 = Yoke Mount 22' 750W PSMH CF!675 -M 5 = Fbmd 20' Mount 12' 50W MH MCF'405 -0 5 =1/2 Adjustable Fitter 12' 7911 MH MCF_407-D ( 1 /!'Adj.Fnefor use on12' housing only) 12' 100W MH MCF!410 -D 8 =Withrnd Mounting (hardware) 1? 175W MH MCF!417 -M (factory- drilled) 16' 175W MH CF :417 - -M i6' 250W MH CF!425 -M 16' 400W MH CF'440 -M 22' 1000W lugs CF!499 -M 12' 35W HPS MCF'503.1 12' 5OW HPS MCF'505 -D 1? 70W HPS MCF!507 --M 12' 100W HPS MCF'510 -M 12' 150W HPS MCF'515 -M 16' 250W HPS CF_525 -M 16' 400W HPS CF!540 -M 22' ' 1000W HPS CF!599 -M Other lamp wattages available - consult factory Reduced envelope lamp. E028 for 320WPSMH Optleam (Fscta q- Inst.Ond) Change Add Attar Description SaftixTo Suffix 2T/V Reactor Ballast noun aeyt 27 120V Reactor ballast (50 -150W HPS 12' housing only) 1 480V ballast paoePsw ,175- mmwuxaro- 1OmsHPSQom 5 Ouad -volt ballast (50 -1OOW MH only) M Tri -volt ballast (320W PSMH, T 7O -1500W MH & 70 -1000W HPS only) (Canada only) Single Fuse' (277V Reactor, 120V. 277V or347V) 27,1,2 or 6 F Dual Fuse' (208V, 240V or 480V) 3,4 or 5 F Overt Standby ( delay- rely type) (Includes 100WCI lamp) Oh27NReactor) 0 Uplight Lens Frame p B u t t o n Photocell* (Factory - installed with all m ountngs other Man 2' Adjustable Flilar) NOTE: n/a on 1000W w/I2OVV; all 480V 27,1,2, 3, 4 or 6 P External Photocell* (Factory.installed) (page 107) For lbdures wt1000W,120V 1 P For Ibdums w/480V 5 P • Fixtures with factory- installed photocell and/or fuse supplied with single voltage ballast. Albs: (Reid-Installed) 12* homing 1rhoeslag 22'housing Wire Guard FWG-12 FWG-16 FWG-22 Backlight Shield SBL -12 SBL -16 S81 -22 Polycarborate (n/a I burs is used in an uptight position) Vandal Shield 1S-12 13-16 LS-22 Button Photocell 0 dp9euuee.uer9dyauawrneo For tbdures w/120V (n/a on 1000W) WAS(- IiokNT For 8xlures w/208,240 or 277V For li,dures w/347V boasting: - Page 90 Catalog Number Log's/Voltage Suffix Hey Page 89 Optical Systems Pages 79-81 des Page107 beating ANemative Pages 124 -125 Muting Brackets Pages 126-127 Poles Pages 128 -133 Catalog i PC -1 PC-2 PC *6 OS bit ft.* Some arp ma r. am 441,12N PO •■• M 1— BOa1 OOFLp N.91414 a0! 4100 MOLIN SOUTH ELEVATION 0 MAINTENANCE WEST ELEVATION 9 MAINTENANCE EAST ELEVATION 0 MAINTENANCE PIPE BOLLARD PLANT sir an.w LANDING 9 EXTERIOR STAIR TRANSVERSE SECT. AT GUARD RAIL a SASE 9 EXTERIOR STAIR seas r -rs FILE COPY Ot ,e tad No* Snot • 7sa 17071 410-7770 10 N M !w. Pn1 Sean rwYY4 MI MO ■■■•••••■•w ENO/ nw.Mm MOLIN I..W n.ben - nmm 0M Mown, f. IS A.M IF QM a.a.b Y• uµ 0,0* halm , Dallr Crwlr uM >w tble Phrt Moor Plan SODA Poor Flan Maintenance Addition MOLIN • ek MO -MA Er lit L i 'on s A y ID 2 111 pm NO 0 i ® v MM.. rai rat; frel KEYPLAN REFLECTED CEILING PLAN OCANVAS CURTAIN M