12/03/2003 Env Bd Packet - Laserfiche WebLink

Home Search

Luminaire The DMS10 luminaire consists of a spun and cast - aluminum exterior housing with large built-in cast - aluminum mounting adaptor/heat sink and flat, spun - aluminum skirt. It can accommodate ballasts up to 400W. When used with a decorative luminous ring (LR option) or luminous dome (LD option) the 250W or 400W ballasts must be remote in the mounting or pole base. The lens assembly,thanksto silicone gaskets along the lens and frame, keeps the housing watertight and is secured by two quarter -turn captive screws. The (ens pivots, providing easy access to the lamp and/or ballast. Lamp Guide DMS20j40 Wattage DMS10/30 DMS10/30 Options LDILR 70 MH 100 MH 175 MH 250 Mil 400 Mil* 35 HPS 50 HPS 70 HPS 100 HPS 150 HPS 250 HPS 400 HPS* • • • • Remote ballast in mounting or pole base. * Consult factory as this wattage requires a remote ballast in a special pole base. 400 MH must use a reduced jacket lamp. DMS10 a, DMS20711, DMS30TM and DMS4O luminaires accommodate H.I.D. or incandescent lamps as shown in the above table. The UL or CSA- recognized CWA -type ballast features a -30F ( -34C1 lamp- starting capacity, a power factor of 90% or better and a regulation of lamp within t10% of rated input voltage. HPS ballasts operate within ANSI trapezoidal limits. The luminaire's lens frame, secured by two captive quater -turn screws, pivots along an hinge to permit easy lamp and/or ballast access. The ballast is integrated in the hood of the luminaire, on a unitized ballast tray, or is remote in the mounting or the pole base. Ordering Sample Similar to the DMS10,the DMS30 is distinguished by its bell- shaped spun - aluminum skirt. The DMS20, on the other hand, features a smaller mounting adaptorthan the DMS10, accepts ballasts of no more than 175W and is not available with the LD and LR options. The DMS40 is similar to the DMS30 except for its smaller mounting adaptor. lt accepts ballast up to 175W only and is not available with the LD and LR options. DMS1O, DINS* DMS30 and DMSM luminaires are UL and CSA approved Optical Systems SG optics Segmented cut -off reflector system set in faceted arc - image duplicating patterns SG1: Asymmetrical (I) SG2: Asymmetrical (II) SG3: Asymmetrical (III) SGO: Symmetrical (V) 21/16" 0 I.D. (52 mm) z n . of C N 24" (610 mm) EPA : 1.00 sq.ft Weight : 40 Ibs (18.1 kg) DMS10 Mountings IF A 180° bent section of extruded aluminum 23/8" (60 mm) O.D., mechani- cally assembled to the side of a pole. • Accepts no ballast. 180° bent section of uded aluminum 23/8" mm) 0.D., welded to ast- aluminum pole aptor and a flat rolled uminum spiral. • 2 ballasts, max. 175W (1,./)JI SGFM: Forward -throw (Gear lamps not included) SE optics Small hydro - formed cut-off reflector system set in faceted arc -image duplicating patterns are also available in type III, IV and V distributions. Please consult factory for details. For further information, refer to the Photometric Guide. A23/8" (60 mm) round aluminum arm welded to a 41/2" (114 mm) O.D. pole adaptor. The moun- ting is complete with two bent decorative rods, spheres and a cast -alu- minum luminaire adaptor. • 2 ballasts, max. 1751N. 0 NM A 180° bent section of extruded aluminum 23/8" (60 mm) O.D., with cast - aluminum decorative spirals, and a pole adap- tor. The mounting slip fits into a 4" (102 mm) pole. • Accepts no ballast. OM 1 i Two straight 1 5/8" (41 mm) O.D. aluminum side -arms welded to a 4" (102 mm) round aluminum pole adaptor and to a cast- aluminum luminaire adaptor. • 2 ballasts, max. 100W. Lamp 100 HPS Luminaire Optical System Voltage Mounting & Configuration DMS30 SG3 120V IF-1A Pole R80 -15 Finish Options GN -TX FS -LD Lumec reserves the right to substitute materials or change the manufacturing process of its products without prior notification.