Laserfiche WebLink
21/16'0 LD. <br />(52 mm) <br />r1 <br />21/W H I.D. <br />(52 mm) <br />1-1 <br />21/16' B I.D. <br />(52 mm) <br />I-1 9 o =I <br />�E <br />' <br />— <br />m <br />w �(4 <br />C <br />EPA: 0.87 sq.ft. <br />Weight :38 Ibs (18.3 kg) <br />DMS20 <br />Mountings <br />PM A 90° bent section of <br />extruded aluminum, 23/6" <br />(60 mm) 0.D., welded to two <br />1" (25 mm) extruded alumi- <br />num arms,two decorative <br />adaptors and a 4" (102 mm) <br />round pole adaptor. <br />• 2 ballasts, max. 100W. <br />p <br />A 23/8" (60 mm) O.D. alu- <br />minum arm welded to a 4" <br />(102 mm) round pole adap- <br />tor and a cast- aluminum <br />luminaire adaptor, with <br />decorative half- sphere. <br />A structural 1/2" (13 mm) <br />rod is welded to the arm <br />and pole adaptor. <br />• 2 ballasts, max. 100W. <br />Configurations <br />-o <br />1A <br />o—o op <br />2 2A <br />olo c-to <br />3 3B <br />4 <br />EPA: 1.00 sq.ft <br />Weight : 40 lbs (18.1 kg) <br />DMS30 <br />Poles <br />25" <br />(635 mm) <br />EPA:0.87 sq.ft. <br />Weight : 36 Ibs (16.3 kg) <br />DMS40 <br />E <br />rE <br />Finishes <br />16 Standard Colors Available <br />12 <br />aes The specially- formulated textured (TX) <br />or non - textured Lumital powder coat is <br />available in a range of 16 standard <br />to colors. This unique coating of thermo- <br />aia setting polyester resins provides a <br />highly- durable UV- resistant exterior <br />finish as per ASTM G7. <br />Lumital coatings are specially formulated <br />for outstanding salt-spray resistance <br />according to ASTM B117 standards. <br />s All surfaces are chemically treated using <br />1113 a four -step (aluminum) or seven -step <br />(steel) process prior to painting. Consult <br />Lumec for complete specifications. <br />244 <br />4 <br />1.22 <br />2 <br />SCL Special Color (liquid) <br />SCP Special Color(powder) <br />Provide a 4" (102 mm) square color chip. <br />0.61 It is possible to order smaller minimal <br />quantities of powder paint at a pre- <br />mium. Your representative will be able <br />n to tell you if a powder coat paint can <br />be developed for your project. <br />Please note that where quantities do <br />not warrant it, Lumec reserves the <br />right to use an oven -cured liquid <br />polyurethane finish. <br />APR4 APR4 <br />& LBC2 <br />D <br />bOtS <br />BC:63/4' BC:63/4' <br />(171 mm) 1171 mm) <br />BC:101/2' BC: 121/2 <br />1267mm) 1318 mm) <br />Consult the Pole Guide for details <br />and the complete line of poles. <br />Options <br />FS <br />HS <br />DL <br />LD <br />Luminaire integrated fuse <br />House shield <br />Polycarbonate drop lens <br />Luminous dome <br />(DMS10and 30 only) <br />LB Luminous ring <br />(DMS10 and 30 only) <br />HB Hinged base <br />(APR4&APS4 poles only) <br />DR" Duplex receptacle <br />(120 volts only) <br />GR* Duplex receptacle with <br />ground fault interrupter <br />(120 volts only) <br />PH Photoelectric cell <br />LS" Provision for loudspeaker outlet <br />BA* Banner arm <br />IP Interior paint (pole only, <br />consult factory for applicable poles) <br />LBC Optional base cover <br />* Consult factory for feasibility with <br />cast - aluminum shafts. <br />Base cover for APR4 & SPR4 poles only <br />(replace standard base cover). <br />Registered Lumec inc. <br />