|
WEATHER PROOFING
<br />1.ALL EXTERIOR WALL OPENINGS, FLASHING, COUNTERFLASHING AND EXPANSION JOINTS SHALL BE
<br />CONSTRUCTED IN SUCH A MANNER AS TO MAKE IT WEATHERPROOF.
<br />2.THE JUNCTION OF THE ROOF AND VERTICAL SURFACES SHALL BE FLASHED AND
<br />COUNTERFLASHED IN A MANNER TO MAKE THEM WEATHERPROOF.
<br />3.PROVIDE FOR ALL TEMPORARY WEATHERPROOFING DURING THE COURSE OF WORK TO ASSURE
<br />PROTECTION AND FULL OPERATION OF THE EXISTING FACILITY.
<br />DOORS, VENTS, AND WINDOWS
<br />1.ALL EGRESS DOORS SHALL BE ABLE TO BE OPENED FROM THE INSIDE WITHOUT USE OF KEY OR
<br />ANY SPECIAL KNOWLEDGE OR EFFORT. ALL EXIT SIGNS SHALL HAVE LETTERS SIX INCHES HIGH
<br />MINIMUM, AND SHALL CONFORM WITH APPLICABLE CODES. REFER TO FLOOR PLANS FOR EXIT
<br />SIGN LOCATIONS.
<br />2.INSTALL PER MANUFACTURER'S PRINTED INSTALLATION INSTRUCTIONS AND RECOMMENDATIONS.
<br />WHERE DETAILED, PROVIDE ALL ADDITIONAL MATERIALS SHOWN OR NOTED. VERIFY ALL OPENING
<br />SIZES, BOTH NEW AND EXISTING PRIOR TO ORDERING. PROVIDE SPACE FOR FLASHING AS
<br />DETAILED. PROVIDE GALVANIC ISOLATION BETWEEN DISSIMILAR MATERIALS.
<br />FINISHES
<br />1.PAINT ALL PAINTABLE ITEMS ATTACHED TO WALLS, CEILING, OR COLUMNS EXCEPT DUCTWORK
<br />AND FLEXIBLE AND/OR MOVABLE PARTS. CONCEAL ALL PIPE AND CONDUIT WHERE WALL FURRING
<br />IS PROVIDED. PRIME ALL MATERIALS WITH MATERIAL COMPATIBLE WITH SUBSTRATE. SEE FINISH
<br />SCHEDULE AND FINISH NOTES.
<br />2.OFFSET STUDS WHERE NEEDED, SO THE FINISH WALL SURFACES WILL BE FLUSH.
<br />3.PROVIDE GALVANIC ISOLATION BETWEEN DISSIMILAR METALS.
<br />4.CEILING SUSPENSION SYSTEMS SHALL BE STABILIZED AGAINST LATERAL MOVEMENT IN
<br />ACCORDANCE WITH THE REQUIREMENTS OF THE IBC, GOVERNING EDITION.
<br />5.CEILING HEIGHTS ARE FROM CONCRETE FLOOR SLAB TO GRID AT ACOUSTICAL TILE CEILING, OR
<br />FINISH AT HARD CEILING.
<br />6.ALL INTERIOR WOOD BLOCKING SHALL BE FIRE TREATED.
<br />EQUIPMENT
<br />1.THE CONTRACTOR SHALL INSTALL ALL EQUIPMENT AND MATERIALS IN ACCORDANCE WITH
<br />MANUFACTURER'S RECOMMENDATIONS UNLESS SPECIFICALLY INDICATED OTHERWISE OR WHERE
<br />LOCAL CODES OR REGULATIONS TAKE PRECEDENCE.
<br />2.VERIFY ALL EQUIPMENT MOUNTING DIMENSIONS PER MANUFACTURER DRAWINGS.
<br />3.PROVIDE SOLID BLOCKING FOR ALL WALL MOUNTED FIXTURES, DEVICES & EQUIPMENT. COORD. W/
<br />ALL DIVISIONS OF THE SPECIFICATIONS TO VERIFY LOCATION REQUIRED.
<br />4.CONTRACTOR SHALL PROVIDE SEISMIC BRACING AND SUPPORT ALL EQUIPMENT AND MATERIALS
<br />PROVIDED.
<br />FIRESTOPPING
<br />1.FIRESTOPPING SHALL BE PROVIDED BY A SINGLE CONTRACTOR FOR ALL TRADES USING A SINGLE
<br />MANUFACTURER'S PRODUCTS (3M OR HILTI).
<br />2.ALL RECESSED PANELS MOUNTED IN FIRE RATED WALLS SHALL BE OF FIRE RATED
<br />CONSTRUCTION TO MATCH RATING OF WALL. (I.E. TRAP PRIMERS, F.E. CABINETS, ETC.)
<br />ELECTRICAL NOTES
<br />1.THESE PLANS ARE DIAGRAMMATIC ONLY, AND NOT TO BE SCALED.
<br />2.ELECTRICAL CONTRACTOR SHALL PROVIDE ALL LABOR, MATERIALS, INSURANCE, EQUIPMENT,
<br />INSTALLATION, CONSTRUCTION TOOLS, TRANSPORTATION, ETC. FOR A COMPLETE AND PROPERLY
<br />OPERATIVE SYSTEM ENERGIZED THROUGHOUT AND AS INDICATED ON DRAWINGS, AS SPECIFIED
<br />HEREIN AND/OR AS OTHERWISE REQUIRED.
<br />3.ALL MATERIALS AND EQUIPMENT SHALL BE NEW AND IN PERFECT CONDITION WHEN INSTALLED
<br />AND SHALL BE OF THE BEST GRADE OR GROUP OF EQUIPMENT. MATERIALS SHALL BE LISTED AND
<br />APPROVED BY UNDER-WRITER'S LABORATORY AND SHALL BEAR THE INSPECTION LABEL "J"
<br />WHERE SUBJECT TO SUCH APPROVAL MATERIALS SHALL MEET WITH APPROVAL OF THE DIVISION
<br />OF INDUSTRIAL SAFETY AND ALL GOVERNING BODIES HAVING JURISDICTION. MATERIALS SHALL BE
<br />MANUFACTURED IN ACCORDANCE WITH APPLICABLE STANDARDS ESTABLISHED BY ANSI, NEMA
<br />AND NBFU.
<br />4.ALL CONDUIT INSTALLED SHALL BE SURFACE MOUNTED UNLESS OTHERWISE NOTED.
<br />5.ELECTRICAL CONTRACTOR SHALL CARRY OUT THE WORK WITH ACCORDANCE WITH ALL
<br />GOVERNING STATE, COUNTY, LOCAL CODES AND O.S.H.A.
<br />6.ELECTRICAL CONTRACTOR SHALL SECURE ALL NECESSARY ELECTRICAL PERMITS, AND PAY ALL
<br />REQUIRED FEES.
<br />7.COMPLETE JOB SHALL BE GUARANTEED FOR A PERIOD OF NO LESS THAN ONE YEAR AFTER THE
<br />DATE OF JOB COMPLETION. ANY WORK, MATERIAL, OR EQUIPMENT FOUND TO BE FAULTY DURING
<br />THAT PERIOD SHALL BE CORRECTED AT ONCE, UPON WRITTEN NOTIFICATION, AT THE EXPENSE
<br />OF THE ELECTRICAL CONTRACTOR.
<br />8.ALL INSTALLATIONS TO MAINTAIN REQUIRED CLEARANCES
<br />9.CONTRACTOR TO SIZE CONDUCTORS PER NEC AND CARRIER REQUIREMENTS AND UPSIZE AS
<br />REQUIRED TO MINIMIZE VOLTAGE DROP.
<br />10.CONTRACTOR TO SIZE CONDUIT PER NEC
<br />11.ALL CONDUIT ONLY (C.O.) SHALL HAVE A PULL WIRE OR ROPE, AND TRUE TAPE.
<br />12.PROVIDE THE OWNER WITH ONE SET OF COMPLETE DIMENSIONS AND CIRCUITS, WITHIN 10
<br />WORKING DAYS OF PROJECT COMPLETION. ELECTRICAL "AS BUILT" DRAWINGS, SHOWING ACTUAL
<br />LOCATION OF CONDUITS.
<br />13.ALL BROCHURES, OPERATING MANUALS, CATALOGS, SHOP DRAWINGS, ETC. SHALL BE TURNED
<br />OVER TO PROJECT MANAGER AT JOB COMPLETION.
<br />14.USE T-TAP CONNECTIONS ON ALL MULTI-CIRCUITS WITH COMMON NEUTRAL CONDUCTOR FOR
<br />LIGHTING FIXTURE. ALL CONDUCTORS SHALL BE COPPER.
<br />15.ALL CIRCUIT BREAKERS, FUSES AND ELECTRICAL EQUIPMENT SHALL HAVE AN INTERRUPTING
<br />RATING NOT LESS THAN THE MAXIMUM SHORT =CIRCUIT CURRENT TO WHICH THEY MAY BE
<br />SUBJECTED, AND A MINIMUM OF 10,000 A.I.C.
<br />16.PATCH, REPAIR, AND PAINT ANY AREA THAT HAS BEEN DAMAGED IN THE COURSE OF THE
<br />ELECTRICAL WORK.
<br />17.IN DRILLING HOLES INTO CONCRETE (WHETHER FOR FASTENING OR ANCHORING PURPOSES OR
<br />PENETRATIONS THROUGH THE FLOOR FOR CONDUIT RUNS, PIPE RUNS, ETC.) IT MUST BE CLEARLY
<br />UNDERSTOOD THAT TENDONS AND RE-BARS WILL NOT BE DRILLED INTO, CUT, OR DAMAGED
<br />UNDER ANY CIRCUMSTANCES.
<br />18.LOCATION OF TENDONS AND RE-BARS ARE NOT DEFINITELY KNOWN AND THEREFORE MUST BE
<br />SEARCHED FOR BY APPROPRIATE METHODS AND EQUIPMENT VIA X-RAY, OR OTHER DEVICES
<br />THAT CAN ACCURATELY LOCATE THE REINFORCING STEEL TENDONS.
<br />19.PENETRATIONS IN FIRE RATED WALLS SHALL BE FIRE STOPPED IN ACCORDANCE WITH
<br />APPLICABLE LOCAL BUILDING CODES. USING U.L. RATED MATERIALS.
<br />20.ELECTRICAL CONTRACTOR IS TO COORDINATE WITH UTILITY COMPANY FOR CONNECTION OF
<br />TEMPORARY AND PERMANENT POWER TO THE SITE. THE TEMPORARY POWER AND ALL HOOK-UP
<br />COSTS SHALL BE PAID BY THE CONTRACTOR.
<br />21.ELECTRICAL CONTRACTOR SHALL SUBMIT SHOP DRAWINGS AND/OR CATALOG CUT-SHEETS ON
<br />ALL NON-SPECIFIED ORIGINAL MATERIALS AND EQUIPMENT, TO PROJECT MANAGER PRIOR TO
<br />COMMENCEMENT OF THE WORK.
<br />22.UPON COMPLETION OF WORK, CONDUCT CONTINUITY AND SHORT CIRCUIT, AS WELL AS,
<br />GROUNDING TEST, GROUNDING TEST SHALL BE PREFORMED BY INDEPENDENT TESTING AGENCY,
<br />WITH WRITTEN REPORT SUBMITTED TO THE PROJECT MANAGER FOR REVIEW AND APPROVAL.
<br />23.CLEAN PREMISES DAILY OF ALL DEBRIS RESULTING FROM WORK AND LEAVE WORK PREMISES IN A
<br />COMPLETE AND UNDAMAGED CONDITION.
<br />24.ALL EXTERIOR WALL PENETRATIONS SHALL BE SEALED WITH POLYSEAM SEALANT.
<br />25.ALL #2 TINNED BARE COPPER DOWNLEADS TO BE PROTECTED BY 1/2" P.V.C. PIPE AND SECURED.
<br />26.COMPRESSION FITTINGS TO BE USED ON ALL CONDUITS (NO SET SCREWS).
<br />27.ALL #6 STRANDED COPPER WITH GREEN INSULATION TO BE ATTACHED WITH CRIMPED DOUBLE
<br />LUG, ATTACHED WITH NUTS, BOLTS AND STAR WASHERS TYPICAL AND NO-OX GREASE BETWEEN
<br />LUG AND BUS BAR.
<br />28.ALL ABOVE GROUND CONDUIT SHALL BE RIGID GALVANIZED CONDUIT WITH WEATHERPROOF
<br />FITTINGS.
<br />29.THE ENTIRE ELECTRICAL INSTALLATION SHALL BE GROUNDED AS REQUIRED BY ALL APPLICABLE
<br />CODES.
<br />GROUNDING
<br />1.ALL METALLIC PARTS OF ELECTRICAL EQUIPMENT WHICH DO NOT CARRY CURRENT SHALL BE
<br />GROUNDED IN ACCORDANCE WITH THE REQUIREMENTS OF THE BUILDING MANUFACTURER,
<br />CARRIER'S AND LANDLORD'S GROUNDING AND BONDING STANDARDS, AND THE NATIONAL
<br />ELECTRICAL CODE.
<br />2.PROVIDE ELECTRICAL GROUNDING AND BONDING SYSTEM INDICATED WITH ASSEMBLY OF
<br />MATERIALS, INCLUDING GROUNDING ELECTRODES, BONDING JUMPERS AND ADDITIONAL
<br />ACCESSORIES AS REQUIRED FOR A COMPLETE INSTALLATION.
<br />3.ALL GROUNDING CONDUCTORS SHALL PROVIDE A STRAIGHT DOWNWARD PATH TO GROUND WITH
<br />GRADUAL BEND AS REQUIRED. GROUNDING CONDUCTORS SHALL NOT BE LOOPED OR SHARPLY
<br />BENT. ROUTE GROUNDING CONNECTIONS AND CONDUCTORS TO GROUND IN THE SHORTEST AND
<br />STRAIGHTEST PATHS POSSIBLE TO MINIMIZE TRANSIENT VOLTAGE RISES.
<br />4.IN BUILDINGS AND/OR NEW TOWERS GREATER THAN 75 FEET IN HEIGHT AND WHERE THE MAIN
<br />GROUNDING CONDUCTORS ARE REQUIRED TO BE ROUTED TO GRADE, THE CONTRACTOR SHALL
<br />ROUTE TWO GROUNDING CONDUCTORS FROM THE ROOFTOP'S, OR TOWER'S GROUND RING, TO
<br />THE EXISTING GROUNDING SYSTEM, THE GROUNDING CONDUCTORS SHALL NOT BE SMALLER
<br />THAN #2 AWG COPPER. ROOFTOP GROUND RING SHALL BE BONDED TO THE EXISTING GROUNDING
<br />SYSTEM, THE BUILDING STEEL COLUMNS, LIGHTNING PROTECTION SYSTEM, AND BUILDING MAIN
<br />WATER LINE (FERROUS OR NONFERROUS METAL PIPING ONLY).
<br />5.TIGHTEN GROUNDING AND BONDING CONNECTORS, INCLUDING SCREWS AND BOLTS, IN
<br />ACCORDANCE WITH MANUFACTURER'S PUBLISHED TORQUE TIGHTENING VALUES FOR
<br />CONNECTORS AND BOLTS. WHERE MANUFACTURER'S TORQUING REQUIREMENTS ARE NOT
<br />AVAILABLE, TIGHTEN CONNECTIONS TO COMPLY WITH TIGHTENING TORQUE VALUES SPECIFIED IN
<br />UL TO ASSURE PERMANENT AND EFFECTIVE GROUNDING. CONTRACTOR SHALL VERIFY THE
<br />LOCATIONS OF GROUNDING TIE-IN-POINTS TO THE EXISTING.
<br />6.ALL UNDERGROUND GROUNDING CONNECTIONS SHALL BE MADE BY THE GROUNDING SYSTEM.
<br />EXOTHERMIC WELD PROCESS AND INSTALLED IN ACCORDANCE WITH THE MANUFACTURER'S
<br />INSTRUCTIONS.
<br />7.ALL GROUNDING CONNECTIONS SHALL BE INSPECTED FOR TIGHTNESS. EXOTHERMIC WELDED
<br />CONNECTIONS SHALL BE APPROVED BY THE INSPECTOR HAVING JURISDICTION BEFORE BEING
<br />PERMANENTLY CONCEALED.
<br />8.APPLY CORROSION-RESISTANCE FINISH TO FIELD CONNECTIONS AND PLACES WHERE FACTORY
<br />APPLIED PROTECTIVE COATINGS HAVE BEEN DESTROYED.
<br />9.A SEPARATE, CONTINUOUS, INSULATED EQUIPMENT GROUNDING CONDUCTOR SHALL BE
<br />INSTALLED IN ALL FEEDER AND BRANCH CIRCUITS.
<br />10.BOND ALL INSULATED GROUNDING BUSHINGS WITH A BARE 6 AWG GROUNDING CONDUCTOR TO A
<br />GROUND BUS.
<br />11.DIRECT BURIED GROUNDING CONDUCTORS SHALL BE INSTALLED AT A NOMINAL DEPTH OF 36"
<br />MINIMUM BELOW GRADE, OR 6" BELOW THE FROST LINE, USE THE GREATER OF THE TWO
<br />DISTANCES.
<br />12.ALL GROUNDING CONDUCTORS EMBEDDED IN OR PENETRATING CONCRETE SHALL BE INSTALLED
<br />IN SCHEDULE 40 PVC CONDUIT.
<br />13.THE INSTALLATION OF A CHEMICAL ELECTROLYTIC GROUNDING SYSTEM IS NOT PERMITTED
<br />UNLESS SPECIFICALLY NOTED.
<br />14.DRIVE GROUND RODS UNTIL TOPS ARE A MINIMUM DISTANCE OF 36" DEPTH OR 6" BELOW FROST
<br />LINE, USING THE GREATER OF THE TWO DISTANCES.
<br />15.IF COAX ON THE ICE BRIDGE IS MORE THAN 6 FT. FROM THE GROUND BAR AT THE BASE OF THE
<br />TOWER, A SECOND GROUND BAR WILL BE NEEDED AT THE END OF THE ICE BRIDGE, TO GROUND
<br />THE COAX CABLE GROUNDING KITS AND IN-LINE ARRESTORS
<br />16.CONTRACTOR SHALL REPAIR, AND/OR REPLACE, EXISTING GROUNDING SYSTEM COMPONENTS
<br />DAMAGED DURING CONSTRUCTION AT THE CONTRACTORS EXPENSE.
<br />17.EXTERIOR GROUND RINGS SHALL BE TESTED AND SHALL HAVE A RESISTANCE TO EARTH OF 5
<br />OHMS OR LESS. IF NOT NOTIFY ENGINEER.
<br />COMMUNICATIONS
<br />GENERAL CABLING
<br />1.ALL INSTALLED CABLES SHALL HAVE SHEATHS (RISER / PLENUM / OUTDOOR / UV RESISTANT)
<br />APPROPRIATE FOR THE MOST RESTRICTIVE ENVIRONMENT WHICH THEY WILL TRAVERSE.
<br />2.ALL CABLING TO BE SUPPORTED AND LACED PER NEC, LOCAL REQUIREMENTS AND TO MEET
<br />CARRIER SPECIFICATIONS.
<br />3.MAINTAIN REQUIRED SEPARATION BETWEEN CONDUCTORS AND OTHER CABLES AS PRESCRIBED
<br />BY CARRIER SPECIFICATIONS AND BEST PRACTICES.
<br />4.ALL FIRE, SMOKE OR DRAFT BARRIERS SHALL BE REPAIRED SUCH THAT THEY MAINTAIN THEIR
<br />INTENDED / REQUIRED RATINGS.
<br />5.PLANS ARE NOT TO BE SCALED. USE DIMENSION CALL-OUTS FOR ESTIMATES. CABLE LENGTHS
<br />ARE SHOWN FOR INFORMATIONAL PURPOSES ONLY AND IT IS THE CONTRACTOR'S
<br />RESPONSIBILITY TO FIELD VERIFY ALL LENGTHS PRIOR TO ORDERING.
<br />FIBER OPTICS
<br />6.VERIFY SINGLE-MODE OR MULTI-MODE AND CONNECTOR TYPE
<br />7.ALL CABLES AND CONNECTORS TO BE PRE-APPROVED, OR AN EXCEPTION OBTAINED PRIOR TO
<br />PURCHASE AND INSTALLATION
<br />8.ALL FIBER STRANDS SHALL BE FUSION SPLICED THROUGHOUT OUT THE LENGTH OF THE RUN AND
<br />BE TERMINATED AT EACH END OF TRUNK UNLESS SPECIFICALLY NOTED.
<br />9.ALL TERMINATIONS TO BE LANDED IN A BULKHEAD OR COILED AND PROTECTED IN A SPLICE CASE
<br />IF BULKHEAD IS SPACE CONSTRAINED.
<br />10.ALL SPLICES TO BE FUSION TYPE AND INDIVIDUAL SPLICES SHALL HAVE A LOSS OF LESS THAN 0.1
<br />dB. ANY SPLICES WITH HIGHER LOSSES TO BE REMADE.
<br />11.ALL FIBERS TO BE TESTED WITH OTDR AND POWER METER. OTDR AND OPTICAL LOSS REPORT
<br />PROVIDED IN CLOSEOUT PACKAGE.
<br />12.ALL FIBER CABLING TO BE INSTALLED IN PROTECTIVE CABLE MANAGEMENT SYSTEMS, DUCT OR BE
<br />ARMORED CABLE WHERE TRAVERSING SHARED SPACE.
<br />COAX AND ANTENNAS
<br />13.ALL ANTENNA MOUNTS SHALL BE INSTALLED IN ACCORDANCE WITH ANSI/TIA-222 AND APPLICABLE
<br />LOCAL CODES
<br />14.ALL COAX TO BE INSTALLED PER CARRIER SPECIFICATIONS, SUPPORTED AT A MINIMUM OF EVERY
<br />4'-0" IN PROPERLY SIZED BLOCKS OR OTHER COAX SUPPORTS U.N.O.
<br />15.ALL COAX TRAVERSING EXTERIOR WALLS SHALL BE PROTECTED ON INTERIOR SIDE WITH
<br />LIGHTNING SURGE SUPPRESSOR GROUNDED TO BUILDING GROUNDING SYSTEM OR STEEL (NOT
<br />LIGHTNING PROTECTION SYSTEM). PROVIDE COAX GROUND KIT AT ANTENNA AND AS REQUIRED
<br />BY CARRIER.
<br />16.ALL COAX TERMINATIONS SHALL BE LOW PIM AND APPROVED BY CARRIER.
<br />17.MAINTAIN MINIMUM BEND RADIUS AND SUPPORT CABLE AS NEEDED TO PROTECT CABLES FROM
<br />SAGGING, KINKING OR BEING CAUGHT.
<br />18.ALL COAX TO BE SWEEP (DTF & RETURN LOSS) AND PIM TESTED WITH PASSING REPORTS
<br />PROVIDED TO CARRIER.
<br />19.PROVIDE 50 OHM LOAD ON ALL UNUSED PORTS.
<br />20.WATERPROOF ALL EXTERIOR CONNECTIONS AND ANY OTHER CONNECTIONS EXPOSED TO
<br />MOISTURE OR CONDENSING ENVIRONMENTS WITH SELF-AMALGAMATING BUTYL TAPE WITH
<br />MINIMUM 1/2" OVERLAP.
<br />21.TORQUE ALL CONNECTIONS TO MANUFACTURER SPECIFICATIONS WITH APPROPRIATE TORQUE
<br />WRENCH.
<br />22.MOUNT GPS ANTENNA ON 1-1/4" SCH. 40 STEEL OR STAINLESS STEEL WITH BURNDY GROUNDING
<br />CLAMP THIN 2° OF VERTICAL.
<br />A 02.05.25 EXHIBIT GW
<br />B 02.20.25 FINAL EXHIBIT GW
<br />Description:Rev:Date:By:
<br />SHEET NUMBER:
<br />SHEET TITLE:
<br />DRAWN BY:CHK BY:APV BY:
<br />PROJECT INFORMATION:
<br />T:
<br />\
<br />N
<br />o
<br />n
<br />-
<br />C
<br />O
<br />\
<br />A
<br />1
<br />N
<br />0
<br />3
<br />7
<br />7
<br />A
<br />\
<br />T
<br />e
<br />m
<br />p
<br />
<br />S
<br />i
<br />t
<br />e
<br />\
<br />A
<br />&
<br />E
<br />\
<br />C
<br />A
<br />D
<br />\
<br />A
<br />1
<br />N
<br />0
<br />3
<br />7
<br />7
<br />A
<br />_
<br />T
<br />e
<br />m
<br />p
<br />
<br />S
<br />i
<br />t
<br />e
<br />_
<br />A
<br />
<br />a
<br />n
<br />d
<br />
<br />E
<br />_
<br />C
<br />D
<br />s
<br />.
<br />d
<br />w
<br />g
<br /> P
<br />L
<br />O
<br />T
<br />
<br />D
<br />A
<br />T
<br />E
<br />:
<br />
<br />2/
<br />2
<br />0
<br />/
<br />2
<br />0
<br />2
<br />5
<br />
<br />B
<br />Y
<br />:
<br />Ga
<br />r
<br />y
<br />
<br />W
<br />a
<br />t
<br />t
<br />s
<br />THIS WORK WAS PREPARED BY MYSELF OR UNDER MY
<br />SUPERVISION. CONSTRUCTION OF THIS PROJECT WILL BE UNDER
<br />MY OBSERVATION. ALL SCALES ARE SET FOR 11"x17"
<br />GW CM CA
<br />PR
<br />E
<br />L
<br />I
<br />M
<br />I
<br />N
<br />A
<br />R
<br />Y
<br />990 SOUTH BROADWAY, DENVER, CO 80209
<br />SITE NAME:
<br />A1N0510A RELO TEMP SITE
<br />SITE ID:
<br />A1N0510A
<br />ALT ID:
<br />SITE ADDRESS:
<br />3303 LANGLEY COURT
<br />LAKE ELMO, MN 55042
<br />SITE COUNTY:
<br />WASHINGTON COUNTY
<br />4751 FOX STREET, DENVER, CO 80216
<br />GENERAL NOTES
<br />GN1.1
|